From: Arjan Fraaij (hpux-admin@zonnet.nl)
Date: Thu Sep 12 2002 - 09:15:57 EDT
In addition, Sam gives the following message when trying to configure
the card!
Configuration of Speed, Duplex and Autonegotiation are not supported
with this version of the Network Interface driver. Please install the
latest revision of the driver product/patch to enable this or contact
your support personnel for further assistance.
Seems to be that the installed product arenīt the correct once, how can
I tell? and which do i need then?
Sam shows the following options but I canīt Use them!
| | Card Type: [ Fast Ethernet -
>] | |
|+| Autoneg: [ OFF -
>] | |
||| Speed (million bps): [ 10 -
>] | |
||| Duplex Mode: [ HALF ->]
Arjan Fraaij
attached mail follows:
Hello,
After reading several post, downloading patches (and installing) I seem
not to be able to put the 100Bt cards on 100Mb?
HP-UX 10.20 OS running
Installed Products:
100BT-EISA-FMT B.10.20.01 100BT/9000 formatter product.
100BT-EISA-KRN B.10.20.01 100BT/9000 EISA kernel products.
100BT-EISA-RUN B.10.20.01 100BT/9000 EISA command
products.
Servers are Model 800 D370 upgraded to D390.
The output of IOSCAN is as follow:
ioscan -funC lan
Class I H/W Path Driver S/W State H/W Type Description
===================================================================
lan 0 8/16/6 lan2 CLAIMED INTERFACE Built-in LAN
/dev/diag/lan0 /dev/i4target
/dev/ether0 /dev/lan0
lan 1 8/20/5/1 token1 CLAIMED INTERFACE EISA card MDG0002
/dev/diag/lan1 /dev/lan1
lan 2 8/20/5/8 btlan0 CLAIMED INTERFACE EISA card INP0500
Is it normal that I donīt see a device path for the btlan0?
The result of Lanscan:
lanscan
Hardware Station Crd Hardware Net-Interface NM MAC HP
DLPI Mjr
Path Address In# State NameUnit State ID Type
Support Num
8/16/6 0x080009559A74 0 UP lan0 UP 4 ETHER
Yes 52
8/20/5/1 0x0000F63ADA14 1 UP lan1 UP 5 802.5
Yes 102
8/20/5/8 0x0060B058E26F 2 UP btlan02 UP 6 ETHER
Yes 136
Lanadmin display result:
LAN INTERFACE STATUS DISPLAY
Thu, Sep 12,2002 14:51:43
Network Management ID = 6
Description = btlan02 Hewlett-Packard LAN adapter
Rev0
Type (value) = ethernet-csmacd(6)
MTU Size = 1500
Speed = 10000000
Station Address = 0x60b058e26f
Administration Status (value) = up(1)
Operation Status (value) = up(1)
Last Change = 0
Inbound Octets = 1213214046
Inbound Unicast Packets = 5499699
Inbound Non-Unicast Packets = 687313
Inbound Discards = 49958
Inbound Errors = 0
Inbound Unknown Protocols = 50086
Outbound Octets = 2318428159
Outbound Unicast Packets = 19019311
Outbound Non-Unicast Packets = 15045
Outbound Discards = 0
Outbound Errors = 0
Outbound Queue Length = 0
Specific = 0
Lanadmin result of trying to put the card to 100Mb
lanadmin -S 100HD 6
Old Speed = 10000000
Unable to change speed: errno = 22
lanadmin -X 100HD 6
Error: This option is not supported for this hardware.
Who can tell me whats going wrong? Could it be that the card is not on
a 100Mb port? Or should I receive an other error message then?
Are the patches installed wrong, is there a way to check this?
Please help!
Arjan Fraaij
--
---> Please post QUESTIONS and SUMMARIES only!! <---
To subscribe/unsubscribe to this list, contact majordomo@dutchworks.nl
Name: hpux-admin@dutchworks.nl Owner: owner-hpux-admin@dutchworks.nl
Archives: ftp.dutchworks.nl:/pub/digests/hpux-admin (FTP, browse only)
http://www.dutchworks.nl/htbin/hpsysadmin (Web, browse & search)
--
---> Please post QUESTIONS and SUMMARIES only!! <---
To subscribe/unsubscribe to this list, contact majordomo@dutchworks.nl
Name: hpux-admin@dutchworks.nl Owner: owner-hpux-admin@dutchworks.nl
Archives: ftp.dutchworks.nl:/pub/digests/hpux-admin (FTP, browse only)
http://www.dutchworks.nl/htbin/hpsysadmin (Web, browse & search)
This archive was generated by hypermail 2.1.7 : Sat Apr 12 2008 - 11:02:19 EDT