From: Patrick B. O'Brien (pobrien@DOIT.NV.GOV)
Date: Mon Nov 25 2002 - 18:10:53 EST
Ferenc,
thanks!!!
-----Original Message-----
From: Ferenc Gyurcsan [mailto:fgyurcsa@AVAILANT.COM]
Sent: Monday, November 25, 2002 1:37 PM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
You have bigger problems than that warning message. What is the output of cllsif?
Warning: There is no service with boot adapter gen_boot on node genoa and on network gen_boot.
Warning: There is no service adapter with standby adapter gen_stby on node genoa and on network gen_stby.
Warning: There is no service with boot adapter rub_boot on node genoa and on network rub_boot.
Warning: There is no service adapter with standby adapter rub_stby on node ruby and on network rub_stby.
Adapter Type Network Net Type Attribute Node IP Address Hardware Address Interface Name Global Name Netmask
gen_boot boot gen_boot ether public genoa 10.131.70.37
gen_stby standby gen_stby ether public genoa 10.131.143.50 en0
gen_svc service gen_svc ether public genoa 10.131.70.36 en1
rub_boot boot rub_boot ether public genoa 10.131.70.35
gen_serial service serial rs232 serial genoa sa1
rub_stby standby rub_stby ether public ruby 10.131.143.51
rub_svc service rub_svc ether public ruby 10.131.70.38
rub_serial service serial rs232 serial ruby s1
A few things you could look into:
-did you reboot the nodes after installation?
I did reboot!
-you have to configure only on one node, and then synchronization will populate the configuration to the other nodes. Is this what you did?
I tried doing one side then the other. From what I understand the cldare -t will write on top of the other node.
-gen_svc and rub_svc should have respective node-names configured.
They do.
--Ferenc
-----Original Message-----
From: Patrick B. O'Brien [mailto:pobrien@DOIT.NV.GOV]
Sent: Monday, November 25, 2002 4:28 PM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
The below is the same in both of my /etc/hosts files.
#HACMP Configurations in the hosts table
10.131.70.36 gen_boot
10.131.70.37 gen_svc
10.131.143.50 gen_stby
10.131.70.35 rub_boot
10.131.70.38 rub_svc
10.131.143.51 rub_stby
# cldare -t (from gen)
clgetactivenodes: Unable to obtain pingable address for rub.
Warning: There is no service with boot adapter gen_boot on node genoa and on net
work gen_boot.
Warning: There is no service adapter with standby adapter gen_stby on node genoa
and on network gen_stby.
Warning: There is no service with boot adapter rub_boot on node genoa and on net
work rub_boot.
Warning: There is no service adapter with standby adapter rub_stby on node ruby
and on network rub_stby.
cldare: Unable to connect to node rub. Any configuration changes
will not be propogated to the node at this time. Any configuration changes
must be propogated to the node before the node will be allowed to join the
cluster.
I can ping both rub_stby and rub_boot no problem?
# cldare -t ( From rub)
clgetactivenodes: Unable to obtain pingable address for rub.
I can ping both cards on both boxes.
Warning: There is no service with boot adapter gen_boot on node genoa and on net
work gen_boot.
Both boxes are running on the xxx_boot lable or IP.
Warning: There is no service adapter with standby adapter gen_stby on node genoa
and on network gen_stby.
Warning: There is no service with boot adapter rub_boot on node genoa and on net
work rub_boot.
Warning: There is no service adapter with standby adapter rub_stby on node ruby
and on network rub_stby.
cldare: Unable to connect to node rub. Any configuration changes
will not be propogated to the node at this time. Any configuration changes
must be propogated to the node before the node will be allowed to join the
cluster.
-----Original Message-----
From: Ferenc Gyurcsan [mailto:fgyurcsa@AVAILANT.COM]
Sent: Monday, November 25, 2002 11:14 AM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
This message tipically happens when you have boot adapters on a node, but no service adapter is associated with it. In some cases, this may be exactly what you want to do.
Describe your configuration, and I can tell you if you should care about this message, or not.
--Ferenc
-----Original Message-----
From: Patrick B. O'Brien [mailto:pobrien@DOIT.NV.GOV]
Sent: Monday, November 25, 2002 2:05 PM
To: aix-l@Princeton.EDU
Subject: HACMP Network Error
I'm getting the below error while trying to implement a Cascading HACMP environment on a pair of 6M1's.
# cldare -t
Warning: There is no service with boot adapter rub_boot on node xxxx and on network rub_boot.
Any thoughts? Thank you.
thank you!
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 22:16:22 EDT