From: Ferenc Gyurcsan (fgyurcsa@AVAILANT.COM)
Date: Tue Nov 26 2002 - 09:09:42 EST
>From HACMP's point of view, you can. Once you have it up and running, fail
the service adapter, which should trigger a swap_adapter event, and the
service and the standby will be swapped. Verify that your switch correctly
picks up the changes.
--Ferenc
-----Original Message-----
From: Patrick B. O'Brien [mailto:pobrien@DOIT.NV.GOV]
Sent: Monday, November 25, 2002 6:13 PM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
I'm using a 1 Gig card for my stby and a 100meg card for my svc/boot. Can I
do that?
-----Original Message-----
From: Ferenc Gyurcsan [mailto:fgyurcsa@AVAILANT.COM]
Sent: Monday, November 25, 2002 1:37 PM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
You have bigger problems than that warning message. What is the output of
cllsif?
A few things you could look into:
-did you reboot the nodes after installation?
-you have to configure only on one node, and then synchronization will
populate the configuration to the other nodes. Is this what you did?
-gen_svc and rub_svc should have respective node-names configured.
--Ferenc
-----Original Message-----
From: Patrick B. O'Brien [mailto:pobrien@DOIT.NV.GOV]
Sent: Monday, November 25, 2002 4:28 PM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
The below is the same in both of my /etc/hosts files.
#HACMP Configurations in the hosts table
10.131.70.36 gen_boot
10.131.70.37 gen_svc
10.131.143.50 gen_stby
10.131.70.35 rub_boot
10.131.70.38 rub_svc
10.131.143.51 rub_stby
# cldare -t (from gen)
clgetactivenodes: Unable to obtain pingable address for rub.
Warning: There is no service with boot adapter gen_boot on node genoa and on
net
work gen_boot.
Warning: There is no service adapter with standby adapter gen_stby on node
genoa
and on network gen_stby.
Warning: There is no service with boot adapter rub_boot on node genoa and on
net
work rub_boot.
Warning: There is no service adapter with standby adapter rub_stby on node
ruby
and on network rub_stby.
cldare: Unable to connect to node rub. Any configuration changes
will not be propogated to the node at this time. Any configuration changes
must be propogated to the node before the node will be allowed to join the
cluster.
I can ping both rub_stby and rub_boot no problem?
# cldare -t ( From rub)
clgetactivenodes: Unable to obtain pingable address for rub.
I can ping both cards on both boxes.
Warning: There is no service with boot adapter gen_boot on node genoa and on
net
work gen_boot.
Both boxes are running on the xxx_boot lable or IP.
Warning: There is no service adapter with standby adapter gen_stby on node
genoa
and on network gen_stby.
Warning: There is no service with boot adapter rub_boot on node genoa and on
net
work rub_boot.
Warning: There is no service adapter with standby adapter rub_stby on node
ruby
and on network rub_stby.
cldare: Unable to connect to node rub. Any configuration changes
will not be propogated to the node at this time. Any configuration changes
must be propogated to the node before the node will be allowed to join the
cluster.
-----Original Message-----
From: Ferenc Gyurcsan [mailto:fgyurcsa@AVAILANT.COM]
Sent: Monday, November 25, 2002 11:14 AM
To: aix-l@Princeton.EDU
Subject: Re: HACMP Network Error
This message tipically happens when you have boot adapters on a node, but no
service adapter is associated with it. In some cases, this may be exactly
what you want to do.
Describe your configuration, and I can tell you if you should care about
this message, or not.
--Ferenc
-----Original Message-----
From: Patrick B. O'Brien [mailto:pobrien@DOIT.NV.GOV]
Sent: Monday, November 25, 2002 2:05 PM
To: aix-l@Princeton.EDU
Subject: HACMP Network Error
I'm getting the below error while trying to implement a Cascading HACMP
environment on a pair of 6M1's.
# cldare -t
Warning: There is no service with boot adapter rub_boot on node xxxx and on
network rub_boot.
Any thoughts? Thank you.
thank you!
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 22:16:22 EDT