From: Bill Zhang (aicc_us@YAHOO.COM)
Date: Tue Sep 10 2002 - 11:19:25 EDT
Sergio,
worked. Thanks a lot!
Bill
--- Sergio Luiz Novaes <algol@LCC.UFMG.BR> wrote:
> A little mistake, the change is on AIX. Execute the
> command:
> chdev -l 'scsi0' -a id='6' '-P'
>
> on your SCSI board to change default ID from 7 to 6.
> Look for correct SCSI
> name (here scsi0). Look also the option -P to do
> changes on database only,
> cos this will require a reboot to take efect,
> specially if you got only one
> SCSI controller or can't offline the controller.
>
> Regards,
>
> Sergio Luiz Novaes
> LCC/UFMG - CENAPAD-MG/CO
> Tel: +55 31 3499 5391/4910
> Fax: +55 31 3499 5390
>
>
>
>
> Bill Zhang
> <aicc_us@YAHOO.CO To:
> aix-l@Princeton.EDU
> M> cc:
> Sent by: IBM AIX
> Subject: Re: hardware needed to install HACMP?
> Discussion List
> <aix-l@Princeton.
> EDU>
>
>
> 09/09/2002 14:26
> Please respond to
> IBM AIX
> Discussion List
>
>
>
>
>
>
> Sergio,
> Can you tell me how to change the initiator ID
> detailly?
> Thanks.
>
> Bill
> --- Sergio Luiz Novaes <algol@LCC.UFMG.BR> wrote:
> > Hi Bill,
> >
> > First, the controller initiator must be
> > different betwen the two
> > controllers, something like 7 for 43p_A and 6 for
> > 43p_B, or you got a
> > conflict. The same for the local disk with ID's
> set
> > to 0 (You have two on
> > the same SCSI bus).
> > I think you can change the initiator on 43p_B,
> > for example, in
> > Maintenance startup.
> >
> > Regarfs,
> >
> > Sergio Luiz Novaes
> > LCC/UFMG - CENAPAD-MG/CO
> > Tel: +55 31 3499 5391/4910
> > Fax: +55 31 3499 5390
> >
> >
> >
> >
> > Bill Zhang
> > <aicc_us@YAHOO.CO To:
> > aix-l@Princeton.EDU
> > M> cc:
> > Sent by: IBM AIX
> > Subject: Re: hardware needed to install HACMP?
> > Discussion List
> > <aix-l@Princeton.
> > EDU>
> >
> >
> > 09/09/2002 04:22
> > Please respond to
> > IBM AIX
> > Discussion List
> >
> >
> >
> >
> >
> >
> > on 43p_A I set the SCSI ID 0 for the local disk
> > (boot
> > disk) and ID 3 for the shared disk. the shared
> disk
> > is
> > connected to rear panel with a ribbon cable and
> the
> > third connector is pluged in to 43p_B which local
> > disks IDs are set to 0 and 1. I booted up 43p_A
> and
> > can see both disks. 43p_B can't be booted up.
> > I'm wondering if both contrallors on these
> machines
> > can sit on one single bus. They both have SCSI ID
> 7
> > as
> > initiators.
> > ribbon bable
> > ________________________
> > | | |
> > | | |
> > 43P_A shared disk 43p_B
> >
> > what is wrong?
> >
> > Thanks a lot!
> >
> > Bill
> >
> >
> > --- Aaron W Morris <Decep@NETSCAPE.NET> wrote:
> > > If you notice, the internal 68-pin connector is
> > the
> > > same as an external 68-pin connector; unless, of
> > > course, the external connector is the mini-lvd
> > type.
> > >
> > > Bill Zhang <aicc_us@YAHOO.COM> wrote:
> > >
> > > >Bill,
> > > >
> > > >I was laughing at myself trying to connect
> > > >43p,disk,43p using a two device ribbon cable.
> > > >obviously it won't work.
> > > >So, a three way cable is the one I need.
> > > >I can even use a internal(68-pin) disk as a
> > > external
> > > >disk?
> > > >
> > > >Bill
> > > >--- Bill Verzal <Bill_Verzal@BCBSIL.COM> wrote:
> > > >> You'd be better served to create a SCSI
> > twintail.
> > > >
> > > >
> > > >> 43p ----- disk ---- 43p
> > > >>
> > > >> BV
> > > >>
> > >
> > >
> >
>
--------------------------------------------------------------------------------------------------------
>
> >
> > > >>
> > > >> Bill Verzal
> > > >> Technical Consultant
> > > >> Forbes Technical Consulting
> > > >> (312) 653-3684
> > > >> bill_verzal@bcbsil.com
> > > >> MailStop: 27.201C
> > > >>
> > > >>
> > > >>
> > > >> Bill Zhang
> > > >> <aicc_us@YAHOO To:
> > > >> aix-l@Princeton.EDU
> > > >> .COM> cc:
> > > >> Sent by: IBM
> > Subject:
> > > >> hardware needed to install HACMP?
> > > >> AIX Discussion
> > > >> List
> > > >> <aix-l@Princet
> > > >> on.EDU>
> > > >>
> > > >>
> > > >> 08/29/2002
> > > >> 10:04 AM
> > > >> Please respond
> > > >> to IBM AIX
> > > >> Discussion
> > > >> List
> > > >>
> > > >>
> > > >>
> > > >>
> > > >>
> > > >>
> > > >> Hi All,
> > > >> I'm trying to install HACMP in my lab.
> > > >> I want to include two nodes(43p) in this
> > cluster.
> > > I
> > > >> have two ethernet cards on each nodes. I need
> a
>
=== message truncated ===
__________________________________________________
Yahoo! - We Remember
9-11: A tribute to the more than 3,000 lives lost
http://dir.remember.yahoo.com/tribute
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 22:16:11 EDT