From: Brewer, Edward \(NIH/OD\) (BREWERE@OD.NIH.GOV)
Date: Wed Nov 24 2004 - 11:10:48 EST
To all,
I have a gigabit ethernet controller that appears to run only as fast as my
100BaseT controller...
Here are the stats
Tru64 5.1b patch kit 4. the system that I am testing is a ES40 that is
clustered to two others...
Here is the output from hwgr for the controller
245:
name = bcm0
category = network
sub_category = Ethernet
model = DEGXA
hardware_rev = BCM5703_A2
firmware_rev =
MAC_address = <REMOVED>
MTU_size = 1500
media_speed = 1000
media_selection = Automatic
media_type = Unshielded Twisted Pair (UTP)
loopback_mode = 0
promiscuous_mode = 0
full_duplex = 1
multicast_address_list = <REMOVED>
interface_number = 1
link = Up
autoneg_enable = 1
registration_time = Tue Nov 23 13:29:42 2004
user_name = (null) (settable)
location = (null) (settable)
software_module = (null)
state = available
state_previous = unknown
state_change_time = none
event_count = 1
last_event_time = Wed Nov 24 10:52:43 2004
access_state = online
access_state_change_time = none
capabilities = 0
indicted = 0
indicted_probability = (null)
indicted_urgency = (null)
disabled = 0
est_seconds = 77573
est_bytesent = 181431005437
est_bloksent = 126024724
est_mbytesent = 0
est_mbloksent = 3659
est_deferred = 0
est_single = 0
est_multiple = 0
est_collis = 0
est_unrecog = 0
est_userbuf = 0
est_latecoll = 0
est_excesscoll = 0
est_carrierfail = 0
est_shortcirc = 0
est_opencirc = 0
est_sndlong = 0
est_sendfail = 0
est_bytercvd = 3138412225
est_blokrcvd = 49028418
est_mbytercvd = 0
est_mblokrcvd = 6418
est_overrun = 0
est_sysbuf = 0
est_unaligned = 0
est_longframe = 0
est_shortframe = 0
est_fcsfail = 0
est_badframe = 0
est_symbolerror = 0
est_recvfail = 0
I am testing this by conneting to another server (Red Hat 3.0 server)
Red Hat controller
Settings for eth1:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: Not reported
Advertised auto-negotiation: No
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
Auto-negotiation: off
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
Link detected: yes
and performing a scp of data.... both 100BaseT and 1000BaseT are running at
the same speeds. I also notice the same speed is achieved for either
interface for backups on veritas. Does anyone have any suggestions?
Thanks,
Lee
This archive was generated by hypermail 2.1.7 : Sat Apr 12 2008 - 10:50:12 EDT