From: Frederico Caldeira (fbc1007@gmail.com)
Date: Fri Sep 29 2006 - 14:36:05 EDT
Hi All,
I have a Fujitsu PW650 server with VxVM/DMP 4.0 MP2 and Solaris 9 connected
to a Clariion Array through a SAN. The two HBAs are a Emulex LP9802. The
following packages are installed:
system CLR-ASL EMC CLARIION Array Support
Library
system DGC-Clar Array Support Librarry for EMC
CLARiiON
system CLR-APM CLR-APM Array Policy Module
system lpfc Emulex LightPulse FC SCSI/IP
Host Bus Adapter driver
I have 14 luns mapped to this server through 4 array controllers. Format
command shows the disk without problem (4 x 14 disks). When I run vxdctl
enable and vxdisk list I see the 14 disks in online state. I created a DG
with 14 disks, a volume using 11 disks and then created and mounted the
filesystem on top of it.
*********************************
*** VXDISK LIST - BEFORE BOOT ***
*********************************
c4t0d0s2 auto:cdsdisk backupdg01 backupdg online
c4t0d1s2 auto:cdsdisk backupdg02 backupdg online
c4t0d2s2 auto:cdsdisk backupdg03 backupdg online
c4t0d3s2 auto:cdsdisk backupdg04 backupdg online
c4t0d5s2 auto:cdsdisk backupdg07 backupdg online
c4t0d6s2 auto:cdsdisk backupdg05 backupdg online
c4t0d7s2 auto:cdsdisk backupdg06 backupdg online
c4t0d8s2 auto:cdsdisk backupdg08 backupdg online
c4t0d9s2 auto:cdsdisk backupdg09 backupdg online
c4t0d10s2 auto:cdsdisk backupdg10 backupdg online
c4t0d11s2 auto:cdsdisk backupdg11 backupdg online
c4t0d12s2 auto:cdsdisk backupdg12 backupdg online
c4t0d13s2 auto:cdsdisk backupdg13 backupdg online
c5t1d4s2 auto:cdsdisk backupdg14 backupdg online
*************************************************************
When I boot the server (boot -r), format command still shows the same
outuput, but VxVM looses access to 12 disks, therefore the DG/Volume failed
to import/start. I need to run the sequence "vxdctl enable; vxvol -g <DG>
startall;mount <mount point>" again to correct the issue. After the "vxdctl
enable" command, the DG are automatic imported.
********************************
*** VXDISK LIST - AFTER BOOT ***
********************************
c4t0d8s2 auto:cdsdisk - - online
c5t1d4s2 auto:cdsdisk - - online
*************************************************************
On a boot messages, I can see that the Clariion array was added by VxVM
after /dev and /devices are configured, but Genesis array are added before.
Is there anything wrong with the boot sequence?
Could anyone solve the problem?
See boot sequence below.
*********************
*** BOOT SEQUENCE ***
*********************
VxVM sysboot INFO V-5-2-3390 Starting restore daemon...
VxVM sysboot INFO V-5-2-3409 starting in boot mode...
NOTICE: VxVM vxdmp V-5-0-34 added disk array DISKS, datype = Disk
NOTICE: VxVM vxdmp V-5-0-34 added disk array 02951, datype = GENESIS
FJSVgid: Fujitsu PCI Gigabit Interface Adapter Driver, v2.4.0-03
fjgi10: network connection up
autonegotiation: on
speed: 1000
flowctrl: symmetric
duplex: full
configuring IPv4 interfaces: fjgi10.
Hostname: fj50in
VxVM INFO V-5-2-3247 starting special volumes ( rootvol swapvol var )...
Configuring /dev and /devices
Configuring the /dev directory (compatibility devices)
VxVM vxvm-startup2 INFO V-5-2-503 VxVM general startup...
NOTICE: VxVM vxdmp V-5-0-34 added disk array CK200033200188, datype =
EMC_CLARiiON
Sep 29 14:32:38 vxvm:vxconfigd: V-5-1-569 Disk group backupdg, Disk
c5t1d4s2: Cannot auto-import group:
Sep 29 14:32:38 vxvm:vxconfigd: Disk group has no valid
configuration copies
*************************************************************
Regards,
Fred
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 23:40:54 EDT