From: Bhavesh Shah (bshah@citadon.com)
Date: Wed Jun 15 2005 - 21:07:32 EDT
Hi Gurus,
I have a Bad disk (bad Media) which is running under Veritas Volume
Manager Control (Vxvm 3.2). When I try to copy files from that file
system it give me an I/O error.The volume is Stripe. Is there a way I
can recover the data by just replacing the disk or need to go through a
procedure?
1) Replace a Bad Disk
2) Delete the Stripe Volume
3) Create a new Stripe Volume
4) Restore Data from Backup
Also I had setup a vxvm-recover script to send me an email alert if
there is any failure occurs but it didn't sent me any notification. I am
able to send test email from that box but VXVM didn't sent me any alert.
Is there is any other place I need to setup email notification from
Vxvm?
Below is the output of vxrpint:
Disk group: archdg
dg archdg default default 3000 1024723131.1283.opsdb1
dm archdg01 c1t0d0s2 sliced 4711 35358848 -
dm archdg02 c1t1d0s2 sliced 4711 35358848 -
dm archdg03 c1t2d0s2 sliced 4711 35358848 FAILING
dm archdg04 c1t3d0s2 sliced 4711 35358848 -
dm archdg05 c1t5d0s2 sliced 4711 35358848 -
dm archdg06 c1t4d0s2 sliced 4711 35358848 -
sd archdg01-01 archvol-01 archdg01 0 35358848 0/0 c1t0d0
ENA
sd archdg02-01 archvol-01 archdg02 0 35358848 1/0 c1t1d0
ENA
sd archdg03-01 archvol-01 archdg03 0 35358848 2/0 c1t2d0
ENA
sd archdg04-01 archvol-01 archdg04 0 35358848 3/0 c1t3d0
ENA
sd archdg06-01 archvol-01 archdg06 0 35358848 4/0 c1t4d0
ENA
sd archdg05-01 archvol-01 archdg05 0 35358848 5/0 c1t5d0
ENA
v archvol - ENABLED ACTIVE 212152320 SELECT
archvol-01 fsgen
pl archvol-01 archvol ENABLED ACTIVE 212153088 STRIPE 6/128
RW
sd archdg01-01 archvol-01 archdg01 0 35358848 0/0 c1t0d0
ENA
sd archdg02-01 archvol-01 archdg02 0 35358848 1/0 c1t1d0
ENA
sd archdg03-01 archvol-01 archdg03 0 35358848 2/0 c1t2d0
ENA
sd archdg04-01 archvol-01 archdg04 0 35358848 3/0 c1t3d0
ENA
sd archdg06-01 archvol-01 archdg06 0 35358848 4/0 c1t4d0
ENA
sd archdg05-01 archvol-01 archdg05 0 35358848 5/0 c1t5d0
ENA
below is the snippet of vxvm-recover script:
# start the watch daemon. This sends E-mail to the administrator when
# any problems are found. To change the address used for sending
problem
# reports, change the argument to vxrelocd.
vxrelocd netops@citadon.com &
# to enable hot sparing instead of hot relocation.
# ( comment out vxrelocd before uncommenting vxspare )
Any help/Pointer will be greatly appreciated
Will Summarize.
TIA
B
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 23:30:54 EDT