From: Dedy Kamal (Dedy.Kamal@metrodata.co.id)
Date: Tue May 17 2005 - 02:16:55 EDT
Guys,
I have new SF V280R, when I trying to turn the power ON there is nothing
happen on the screen (black screen), but when I switch the key on diagnostic
mode the error messages comes like bellow, I just want to make sure is it
hardware problem or not ? and after POST installation complete I can't
continue boot from default bootdisk
Please advice
Error messages during POST :
@(#)OBP 4.13.0 2004/01/19 18:27 Sun Fire 280R
Power-On Reset
Executing Power On SelfTest
0:0>
0:0>@(#) Sun Fire[TM] V280, Sun Blade[TM] 1000 POST 4.13.0 2004/03/15 19:13
/export/common-source/firmware_re/post/post-build-4.13.0/Camelot/excal
/integrated (firmware_re)
0:0>Copyright ) 2004 Sun Microsystems, Inc. All rights reserved
SUN PROPRIETARY/CONFIDENTIAL.
Use is subject to license terms.
0:0>Jump from OBP->POST.
0:0>diag-switch? configuration variable set TRUE.
0:0>Diag level set to MIN.
0:0>Verbosity level set to 0.
0:0>MFG scrpt mode set to NONE
0:0>I/O port set to serial TTYA.
0:0>Done with First Init, reset system.
0:0>Current CPU frequency is 400 MHz.
0:0> Resetting to 1200
0:0>Clock Synth Reset.
0:0>
0:0>Start selftest...
0:0>CPUs present in system: 0:0 1:0
0:0>Test CPU(s).....
0:0>Init CPU
0:0> UltraSparc_III_plus Version 11.1
0:0>DMMU Registers Access
0:0>DMMU TLB DATA RAM Access
0:0>DMMU TLB TAGS Access
0:0>IMMU Registers Access
0:0>IMMU TLB DATA RAM Access
0:0>IMMU TLB TAGS Access
0:0>Probe Ecache
0:0> Size = 00000000.00800000...
0:0>Ecache Data Bitwalk
0:0>Ecache Address Bitwalk
0:0>Scrub and Setup Ecache
0:0>Setup and Enable DMMU
0:0>Setup DMMU Miss Handler
0:0>Test and Init Temp Mailbox
1:0>Init CPU
1:0> UltraSparc_III_plus Version 11.1
1:0>DMMU Registers Access
1:0>DMMU TLB DATA RAM Access
1:0>DMMU TLB TAGS Access
1:0>IMMU Registers Access
1:0>IMMU TLB DATA RAM Access
1:0>IMMU TLB TAGS Access
1:0>Probe Ecache
1:0> Size = 00000000.00800000...
1:0>Ecache Data Bitwalk
1:0>Ecache Address Bitwalk
1:0>Scrub and Setup Ecache
1:0>Setup and Enable DMMU
1:0>Setup DMMU Miss Handler
1:0>Test and Init Temp Mailbox
0:0>Init Scan/I2C.....
0:0>Initializing Scan Database
0:0>BBC: 1483203b
0:0>SCSI: 15060045
0:0>ICHIP: 0d1e203b
0:0>RIO: 13e5d03b
0:0>IO-Bridge: 307be06d
0:0>CPMS0: 1142903b
0:0>CPMS1: 1142903b
0:0>CPMS2: 1142903b
0:0>CPMS3: 1142903b
0:0>CPMS4: 1142903b
0:0>CPMS5: 1142903b
0:0>Init I2C
0:0>Unquiesce Safari
0:0>Blast Fans
0:0>Set Trip Temp CPU 0 to 110C
0:0>Set Trip Temp CPU 1 to 110C
0:0>THUR APR 21 7:07:11 GMT 5
0:0>Safari quick check
0:0> to IO-bridge_0
0:0>Safari full check
0:0> to IO-bridge_0
0:0>Basic Memory Test.....
0:0>Probe and Setup Memory
0:0>INFO: 1024MB Bank 0
0:0>INFO: No memory detected in Bank 1
0:0>INFO: 1024MB Bank 2
0:0>INFO: No memory detected in Bank 3
0:0>
0:0>Data Bitwalk on Master
0:0> Test Bank 0.
0:0> Test Bank 2.
0:0>Address Bitwalk on Master
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 0: 00000000.00000000 to
00000000.40000000.
0:0>
0:0>INFO: Addr walk mem test on CPU 0:0 Bank 2: 00000002.00000000 to
00000002.40000000.
0:0>Set Mailbox
0:0>Setup Final DMMU Entries
0:0>Post Image Region Scrub
0:0>Run POST from Memory
0:0>Verifying checksum on copied image.
0:0>The Memory's CHECKSUM value is 89c2.
0:0>The Memory's Content Size value is 9ad4c.
0:0>Success... Checksum on Memory Validated.
1:0>Safari quick check
1:0> to IO-bridge_0
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG = ERROR: IO-Bridge Fault Check 170.
1:0>END_ERROR
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG = IO-Bridge Error - UE AFSR Reg,
address 00000400.04410040
observed 800002ff.01800109
1:0>END_ERROR
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG = IO-Bridge Error - UE AFAR Reg,
address 00000400.04410048
observed 00000e00.04417000
1:0>END_ERROR
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG =
ERROR:0 AFSR Error 00000002.00000109, AFAR
00000400.04417010.
1:0>END_ERROR
1:0> CE bit: Correctable system data ECC error
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG = Safari quick check error CPU_1 to IO-bridge_0
1:0>END_ERROR
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG =
*** Test Failed!! ***
1:0>END_ERROR
1:0>
1:0>ERROR: TEST = Safari quick check
1:0>H/W under test = Motherboard/Centerplane Safari, CPU Slot B
1:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
1:0>MSG = ERROR: Fatal CPU error on slave 1:0, offlining this cpu.
1:0>END_ERROR
0:0>
0:0>ERROR: TEST = Run POST from Memory
0:0>H/W under test = CPU0, All CPU0 Memory
0:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
0:0>MSG = ERROR: Unknown type request 00000000.00000066 in global_gnt.
0:0>END_ERROR
0:0>INFO: Reset Module with CPUs 1 3, both have been offlined.
0:0>Memory Block.....
0:0>Print Mem Config
0:0>Caches : Icache is ON, Dcache is ON, Wcache is ON, Pcache is ON.
0:0>Memory in non-interleave config:
0:0> Bank 0 1024MB : 00000000.00000000 -> 00000000.40000000.
0:0> Bank 2 1024MB : 00000002.00000000 -> 00000002.40000000.
0:0>Scrub Memory
0:0>Quick Block Mem Test
0:0>Quick Test 16777216 bytes at 00000000.00600000
0:0>40% Done...
0:0>Flush Caches
0:0>Get code in ecache.
0:0>IO-Bridge Tests.....
0:0>IO-Bridge unit 0 init test
0:0>
0:0>ERROR: TEST = IO-Bridge unit 0 init test
0:0>H/W under test = Motherboard/Centerplane IO-Bridge 0, CPU, I/O Board
0:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
0:0>MSG = IO-Bridge Error - 64bit Cntl Reg Register,
address 00000400.04410000
expected 02555555.00800000
observed 0255f7dd.00800000
wrote 02555555.00800000
0:0>END_ERROR
0:0> FAILED
0:0> FAILED
0:0>
0:0>ERROR: TEST = IO-Bridge unit 0 init test
0:0>H/W under test = Motherboard/Centerplane IO-Bridge 0, CPU, I/O Board
0:0>Repair Instructions: Replace items in order listed by 'H/W under test'
above.
0:0>MSG =
*** Test Failed!! ***
0:0>END_ERROR
0:0>FPU Registers and Data Path
0:0>FPU Move Registers
0:0>FSR Read/Write
0:0>FPU BLOCK REG TEST
0:0>
0:0>Enable Errors.....
0:0>Turn error traps on
0:0>ERROR:
0:0> POST toplevel status has the following failures:
0:0> CPU1
0:0> IO-Bridge0
0:0> Mother Board
0:0> Safari B
0:0> POST failed the following motherboard devices:
0:0> IO-Bridge0
0:0> Safari B
0:0>END_ERROR
0:0>POST: Return to OBP.
0:0>Return to OBP, FAIL
@(#)OBP 4.13.0 2004/01/19 18:27 Sun Fire 280R
POST Results: Cpu 0
%o0 ffff.ffff.ffff.ffff
%o1 ffff.ffff.ffff.ffff
%o2 ffff.ffff.ffff.ffff
POST Results: Cpu 1
%o0 22ba.29ae.809c.1420
%o1 c0e4.c63f.ce40.58a0
%o2 f379.bcbe.9e73.b492
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.0010.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB (small-footprint mode) Done
MMUs ON
Find dropin, Copying Done, Size 0000.0000.0000.6f90
Jump to RAM Done
Find dropin, Copying Done, Size 0000.0000.0001.25d0
ttya initialized
Start Reason: Initialize Machine
Configuring the machine:
@(#)OBP 4.13.0 2004/01/19 18:27 Sun Fire 280R
Loading Configuration
Membase: 0000.0000.0000.0000
MemSize: 0000.0000.8000.0000
Clearing TLBs Done
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.6f90
Jump to RAM Done
Find dropin, (copied), Decompressing Done, Size 0000.0000.0006.2da0
ttya initialized
System Reset: CPU Reset (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)
memory-controller
Probing gptwo at 1,0 Invalid FCode start byte at fff1e000
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device
SUNW,fru-device
Loading onboard drivers: ebus flashprom i2c nvram idprom dimm-fru
dimm-fru dimm-fru dimm-fru bbc power i2c cpu-fru temperature cpu-fru
temperature fan-control motherboard-fru ioexp ioexp ioexp
fcal-backplane remote-system-console power-distribution-board
power-supply power-supply rscrtc beep rtc gpio pmc parallel
rsc-control rsc-console serial
System Reset: CPU Reset (SPOR) (PLL)
Probing gptwo at 0,0 SUNW,UltraSPARC-III+ (1200 MHz @ 8:1, 8 MB)
memory-controller
Probing gptwo at 1,0 Invalid FCode start byte at fff1e000
Probing gptwo at 8,0 pci pci
Loading Support Packages: kbd-translator obp-tftp SUNW,i2c-ram-device
SUNW,fru-device
Loading onboard drivers: ebus flashprom i2c nvram idprom dimm-fru
dimm-fru dimm-fru dimm-fru bbc power i2c cpu-fru temperature cpu-fru
temperature fan-control motherboard-fru ioexp ioexp ioexp
fcal-backplane remote-system-console power-distribution-board
power-supply power-supply rscrtc beep rtc gpio pmc parallel
rsc-control rsc-console serial
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.13.0, 2048 MB memory installed, Serial #59137837.
Ethernet address 0:3:ba:86:5f:2d, Host ID: 83865f2d.
Power On Selftest Failed.
CPU: 0 cause: OBMD
Initializing 1MB of memory at addr 7fef0000 -
Initializing 1MB of memory at addr 7fec0000 -
Initializing 1MB of memory at addr 7fea0000 -
Initializing 15MB of memory at addr 7f000000 -
Initializing 2032MB of memory at addr 0 -
Aborting auto-boot sequence.
Tks
DKA
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 23:30:43 EDT