From: sudesh.shetty@wipro.com
Date: Mon Mar 28 2005 - 05:39:56 EST
Hi Gurus,
I am facing with a problem. One of my customer has a SF1280
server which is connected to an EMC CX300 box through 2 HBA cards ( connected
to 33Mhz PCI slot). Now customer had purchased one more CX300 server and 1 new
HBA cards last month.At that time, I had installed the HBA on the server
(totalling to 3 HBA) and rebooted the server. When the server had reached the
OBP level , it detected three HBA successfully after which i upgraded the
firmware of the HBA.
Now, customer has purchased one more HBA for redundancy totalling it to four
HBA's connected to 4 separate PCI (33MHz) slots.
But now, when i install the fourth HBA, and reboot the server i get the
following message:-
{/N0/SB4/P1} DCB_ENTER_OBP command succeeded
{/N0/SB4/P2} DCB_ENTER_OBP command succeeded
{/N0/SB4/P3} DCB_ENTER_OBP command succeeded
Entering OBP ...
lom>
*** FCode LP10000 PCI_Bus (lpfc) Version 1.40a0 ***
Cannot Configure Port.
*** FCode LP10000 PCI_Bus (lpfc) Version 1.40a0 ***
*** FCode LP10000 PCI_Bus (lpfc) Version 1.40a0 ***
*** FCode LP10000 PCI_Bus (lpfc) Version 1.40a0 ***
Sun Fire V1280
OpenFirmware version 5.13.0014 (07/15/03 15:09)
Copyright 2001-2003 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
SmartFirmware, Copyright (C) 1996-2001. All rights reserved.
{0} ok
{0} ok
after which both the LED's on the HBA go blank. But "prtdiag" shows me all the
HBA cards whereas in "lputil" command there is only 3 cards detected.
# prtdiag |more
System Configuration: Sun Microsystems sun4u Sun Fire V1280
System clock frequency: 150 MHZ
Memory size: 24GB
======================================= CPUs
=======================================
E$ CPU CPU Temperature Fan
CPU Freq Size Impl. Mask Die Ambient Speed Unit
------ -------- ---------- ------ ---- -------- -------- ----- ----
SB0/P0 1200 MHz 8MB US-III+ 6.0 49 C 30 C
SB0/P1 1200 MHz 8MB US-III+ 6.0 48 C 29 C
SB0/P2 1200 MHz 8MB US-III+ 6.0 48 C 29 C
SB0/P3 1200 MHz 8MB US-III+ 6.0 48 C 30 C
SB2/P0 1200 MHz 8MB US-III+ 6.0 47 C 28 C
SB2/P1 1200 MHz 8MB US-III+ 6.0 45 C 29 C
SB2/P2 1200 MHz 8MB US-III+ 6.0 47 C 29 C
SB2/P3 1200 MHz 8MB US-III+ 6.0 47 C 29 C
SB4/P0 1200 MHz 8MB US-III+ 6.0 44 C 29 C
SB4/P1 1200 MHz 8MB US-III+ 6.0 48 C 30 C
SB4/P2 1200 MHz 8MB US-III+ 6.0 48 C 31 C
SB4/P3 1200 MHz 8MB US-III+ 6.0 46 C 31 C
==================================== IO Devices
====================================
Bus Freq
Brd Type MHz Slot Name Model
--- ---- ---- ---------- ----------------------------
--------------------
0 pci 33 PCI0 SUNW,XVR-100 (display) SUNW,375-3126
0 pci 33 PCI1 scsi-pci1000,f (scsi-2)
0 pci 33 PCI1 scsi-pci1000,f (scsi-2)
0 pci 66 PCI5 lpfc-pci10df,fa00 (scsi) LP10000
0 pci 33 PCI2 lpfc-pci10df,fa00 (scsi) LP10000
0 pci 33 PCI3 lpfc-pci10df,fa00 (scsi) LP10000
0 pci 33 PCI4 lpfc-pci10df,fa00 (scsi) LP10000
0 pci 66 1 pci108e,abba (network) SUNW,pci-ce
0 pci 66 2 scsi-pci1000,21 (scsi-2)
0 pci 66 2 scsi-pci1000,21 (scsi-2)
0 pci 66 2 pci108e,abba (network) SUNW,pci-ce
0 pci 33 3 pci1095,646 (ide)
0 pci 33 4 bootbus-controller-sgsbbc SUNW,sgsbbc
#/usr/sbin/lpfc/lputil
LightPulse Common Utility for Solaris/SPARC. Version 1.6a8 (03/03/2004).
Copyright (c) 2003, Emulex Network Systems, Inc.
Emulex Fibre Channel Host Adapters Detected: 3
Host Adapter 0 (lpfc0) is an LP10K (Ready Mode)
Host Adapter 2 (lpfc2) is an LP10K (Ready Mode)
Host Adapter 3 (lpfc1) is an LP10K (Ready Mode)
I tried to swap the slot also, but then too the same card gives me the
problem. Is the card gone faulty???????????????? If So why the four entries in
prtdiag???????
Please would appreciate any HELPPPPPPPP???
Regards
SUDESH
Confidentiality Notice
The information contained in this electronic message and any attachments to
this message are intended
for the exclusive use of the addressee(s) and may contain confidential or
privileged information. If
you are not the intended recipient, please notify the sender at Wipro or
Mailadmin@wipro.com immediately
and destroy all copies of this message and any attachments.
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 23:30:25 EDT