From: Mr Rene Occelli (rene@polytech.univ-mrs.fr)
Date: Fri Mar 26 2004 - 07:27:59 EST
Hi
It's me again with my board failure. After many tries, I have found a GOOD
serial cable with two GOOD connectors and reboot the machine that gives
me a lot fo messages in diag mode.
Here some parts where the errors appear ( can send entire file on demand)
0,0>Displaying PROM Versions
0,0>Slot 0 CPU/Memory OBP 3.2.28 2000/12/20 12:24 POST 3.9.28 2000/12/20
12:29
0,0>Slot 1 IO Type 1 FCODE 1.8.28 2000/12/20 12:20 iPOST 3.4.28 2000/12/20
12:28
0,0>Slot 2 CPU/Memory OBP 3.2.28 2000/12/20 12:24 POST 3.9.28 2000/12/20
12:29
0,0>Slot 3 CPU/Memory OBP 3.2.28 2000/12/20 12:24 POST 3.9.28 2000/12/20
12:29
.....
0,0>Do OPTIMAL INTLV
0,0> Board 0 AC rev 5 RCTIME = 0 (Tras 71)
0,0> Board 2 AC rev 5 RCTIME = 0 (Tras 71)
0,0> Board 3 AC rev 5 RCTIME = 0 (Tras 71)
0,0> Board 0 AC rev 5 RCTIME = 0 (Tras 71)
0,0> Memory Refresh Enable
0,0>Board 0 SIMMs Test
Board 0 SIMMs Test
0,0> MP Memory SIMM Clear Test
0,0> Memory Size is 1024Mbytes
0,0> CPU MID 1 clearing 00000000.00004000 to 00000000.0aa00000
0,0> CPU MID 4 cleari0,0>FATAL ERROR
0,0> At time of error: POST was testing Board 0 Memory
0,0> Diagnosis: Board 3, Dtag A (UPA Port 0), AC
0,0>Log Date: Mar 26 11:04:59 GMT 2004
0,0>
0,0>RESET INFO for CPU/Memory board in slot 3
0,0> AC ESR 00000020.00000000 DT_PERRA
0,0> DC[0] 00
0,0> DC[1] 00
0,0> DC[2] 00
0,0> DC[3] 00
0,0> DC[4] 00
0,0> DC[5] 00
0,0> DC[6] 00
0,0> DC[7] 00
0,0> FHC CSR 00010030 SYNC BRD_LED_M BRD_LED_R
0,0> FHC RCSR 02000000 FATAL
0,1>
0,0>
0,1>@(#) POST 3.9.28 2000/12/20 12:29
0,0>@(#) POST 3.9.28 2000/12/20 12:29
......
0,0>Reconfig memory due to FATAL RESET
0,0>Reconfig memory due to new CONFIG POLICY
0,0>Reconfig memory due to DIAG_LEVEL
....
0,0> System Board Status
0,0>-----------------------------------------------------------------
0,0> Slot Board Status Board Type Failures
0,0>-----------------------------------------------------------------
0,0> 0 | Normal | CPU/Memory |
0,0> 1 | Normal | IO Type 1 |
0,0> 2 | Normal |+CPU/Memory |
0,0> 3 | Low Power Mode | CPU/Memory | AC DTags0
0,0> 4 | Not installed | |
0,0> 5 | Not installed | |
0,0> 6 | Not installed | |
0,0> 7 | Not installed | |
0,0> 16 | Normal | Clock Board |
0,0>-----------------------------------------------------------------
.....
Clock board TOD does not match TOD on any IO board.
....
Then the machine boots OK with board 3 disabled
Can someone give me more explanations on this problem ?
(I know the last message but don't remember exactly the command to reset clock
on all boards)
Thanks
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
+ Rene OCCELLI +
+ Polytech Marseille IUSTI Lab. C.N.R.S. U.M.R. 6595 +
+ Technopole de Chateau Gombert +
+ 5 Rue Enrico FERMI +
+ 13453 MARSEILLE Cedex 13 France +
+ Tel: (33)04 91 10 69 37 04 91 10 69 38 +
+ Fax: (33)04 91 10 69 69 +
+ Email: rene@polytech.univ-mrs.fr +
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++
_______________________________________________
sunmanagers mailing list
sunmanagers@sunmanagers.org
http://www.sunmanagers.org/mailman/listinfo/sunmanagers
This archive was generated by hypermail 2.1.7 : Wed Apr 09 2008 - 23:28:21 EDT